Opens in a new tab

Materials Testing Services

Materials testing measures the composition, structure and properties of a material to show how it will perform, why it failed or whether it meets its specification. Covalent’s scientists run more than 80 analytical techniques in our Sunnyvale lab and explain what the results mean for your product.Trusted by 1,500+ companies, from startups to global manufacturers

What Is Materials Testing?

Materials testing is the measurement of a material’s chemical, physical, mechanical, thermal, optical or electrical properties. Engineers use it to choose and develop materials, control production, qualify suppliers, and find the root cause when a part fails.

A single question often needs several techniques. Identifying a residue on a failed part, for example, may combine SEM-EDS for the elements, FTIR for the organic chemistry and XPS for the top few nanometers of the surface. Our scientists choose the combination and interpret the results together.

Destructive vs nondestructive testing

Nondestructive testing examines a part without changing it. Micro-CT, scanning acoustic microscopy and 2D X-ray find voids, cracks and delamination inside a part, so it can still be used or tested further.

Destructive testing cuts, loads or consumes the sample to measure it. Cross-sections, tensile testing and chemical digestion for ICP fall into this group.

When samples are limited, we start nondestructive and then target the destructive analysis.

Types of Materials Testing

Choose a type to see the questions it answers and the techniques we use.

Mechanical Testing

Strength, stiffness, hardness and adhesion, from bulk parts to thin coatings.

  • Tensile
  • Flexural
  • Nanoindentation
  • Nano scratch
  • DMA
  • Rheology
Mechanical Testing

Chemical & Compositional Analysis

Which elements and compounds are present, how much, and where.

  • ICP-OES
  • ICP-MS
  • FTIR
  • Raman
  • NMR
  • XRF
Chemical & Compositional Analysis

Thermal Analysis

Melting point, Tg, cure, thermal stability, filler content and expansion.

  • DSC
  • TGA
  • TMA
  • DMA
  • IR thermography
Thermal Analysis

Surface & Interface Analysis

Surface chemistry, cleanliness, roughness and what happens at interfaces.

  • XPS
  • ToF-SIMS
  • AFM
  • Contact angle
  • WLI
Surface & Interface Analysis

Microstructure & Metallurgical Analysis

Grains, phases, inclusions and fractures, tied to how the material was processed.

  • SEM
  • FIB-SEM
  • TEM
  • XRD
  • Metallography
Metallurgical Analysis

Nondestructive Inspection

Voids, cracks and delamination inside parts, packages and assemblies.

  • Micro-CT
  • SAM
  • 2D X-ray
Micro-CT

Powder & Particle Testing

Particle size, shape, density, surface area and flow.

  • Laser diffraction
  • DLS
  • BET
  • Gas pycnometry
  • Tap density
Powder Testing

Coating Testing

Thickness, composition, adhesion and hardness of coatings and platings.

  • Ellipsometry
  • XPS
  • Nano scratch
  • Nanoindentation
  • Cross-sections
Coating Testing

Polymer & Plastic Analysis

Polymer identity, additives, thermal behavior and aging.

  • FTIR
  • DSC
  • TGA
  • GPC
  • GC-MS
Polymer & Plastic Analysis

Metals Testing

Alloy composition, microstructure, hardness, corrosion and metal failures.

  • EDXRF
  • GDOES
  • ICP-OES
  • SEM-EDS
  • Hardness
Metals Testing

Optical Characterization

Film thickness, n and k, transmittance, reflectance, color and bandgap.

  • Ellipsometry
  • UV-Vis-NIR
  • PL
  • Raman
Optical Characterization

Electrical Testing

Sheet resistance, carrier profiles and device-level electrical behavior.

  • 4-point probe
  • SCM
  • Nanoprobing
4-Point Probe

Need a technique we don’t run in-house? We can source it through Covalent Connect, our network of trusted partner labs. Browse all 80+ techniques →

When You Need Materials Testing

Most projects start with one of these questions.

Developing a material or process

R&D support and process development, as a single project or an ongoing program with our scientists on your team.

Enterprise Metrology Solutions

Something failed

Root cause of cracks, shorts, delamination, corrosion and field returns.

Failure Analysis

Controlling production

Lot-to-lot checks of composition, thermal, mechanical and surface properties.

Quality Control Testing

Qualifying a supplier

Confirm incoming materials match their specification.

Material Verification

Finding contamination

Identify particles, films and residues, and where they came from.

Contamination Analysis

Understanding a product

How it’s built and what it’s made of: teardown, reverse engineering and deformulation.

Advanced Product Teardowns

Supporting a legal matter? See Product Liability Testing.

Materials Testing Standards

We test to ASTM, ISO, IPC and USP standards when your specification calls for them, or to a method designed around your question. Below are common standards by type of test. It isn’t a complete list, so if you need a standard that isn’t shown, tell us which one and we’ll confirm we can follow it.

Mechanical
TestCommon standards
Tensile and flexural ASTM D638 (tensile properties of plastics), ASTM D882 (thin plastic films), ASTM E8 (tension testing of metals), ASTM D790 (flexural properties), with an extensometer compliant with ASTM E83 / ISO 9513
Hardness ASTM E18 and ISO 6508 (Rockwell), ASTM E10 and ISO 6506 (Brinell), ASTM D2240 and ISO 868 (Shore durometer)
DMA ASTM D4065 (DMA practice and reporting), ASTM D5026 / D5023 / D5024 (tension, flexure and compression), ASTM E1640 (glass transition by DMA), ISO 6721 (dynamic mechanical properties of plastics)
Thermal
TestCommon standards
DSC ASTM D3418 (polymer transition temperatures and enthalpies), ISO 11357 (DSC of plastics), ASTM E1356 (glass transition), ASTM E1269 (specific heat capacity), ASTM E928 (purity)
TGA ASTM E1131 (compositional analysis), ISO 11358 (TGA of polymers), ASTM E2550 (thermal stability), ASTM E1641 (decomposition kinetics)
TMA ASTM E831 (CTE), ASTM E1545 (glass transition), ASTM E2347, ISO 11359-2, and IPC-TM-650 2.4.24 for Tg and z-axis expansion of PCB laminates qualified to IPC-4101
Chemical
TestCommon standards
CHNS/O elemental analysis ASTM D5291, ASTM D4239, ASTM D3176, ISO 29541, ISO 16948, ISO 16994, ISO 16634
Surface
TestCommon standards
Surface roughness (WLI, confocal microscopy, AFM) ISO 25178 (areal parameters such as Sa, Sq and Sz), ISO 21920 and ISO 4287 (profile parameters such as Ra, Rq and Rz)
Powders & particles
TestCommon standards
Laser diffraction particle size ISO 13320, USP <429>
Tap density USP <616>, ASTM B527 (metal powders), ISO 3953
SAXS ISO 17867 (particle size analysis by SAXS)
Capillary flow porometry ASTM F316 (pore size and bubble point of membrane filters)
Electronics
TestCommon standards
PCB cross-sections IPC-TM-650 2.1.1 (microsectioning), evaluated against IPC-A-600 and IPC-6012; ASTM E3 and ASTM E407 for metals
IPC inspection IPC-A-610, IPC-A-620, IPC-6012
Dye and pry IPC-TM-650, IPC-A-610
Magnetic & construction
TestCommon standards
Vibrating sample magnetometry ASTM A894 (saturation magnetization), ASTM A342, ASTM A773, ASTM A977, ASTM A596, ASTM A772
Petrographic analysis ASTM C856 (hardened concrete), ASTM C295 (aggregates), ASTM C457 (air voids), and related ASTM C and D methods

Covalent is accredited to ISO/IEC 17025 across 60+ standardized and proprietary methods. See our accreditations and scope →

How a Materials Testing Project Works

From your first question to results you can act on, usually within 5–7 business days.

  1. 1

    Tell us the question

    Describe the material, what you’re seeing and what decision the results will support.

  2. 2

    Get a test plan and quote

    A scientist recommends the techniques. Most quotes go out within one business day.

  3. 3

    Ship your samples

    We send prep and shipping instructions, and sign NDAs on request.

  4. 4

    Review the results

    Data and a written report in your MyData portal, with a scientist to walk you through them.

How to Choose a Materials Testing Lab

Instruments matter, but the answer depends on the people who choose the method and read the data. Look for:

Accreditation: ISO/IEC 17025, with the methods you need on its scope.

Scientists who interpret: A report that explains what the data means for your product, not only raw results.

Range of techniques: Enough methods under one roof to answer the whole question, with a partner network for the rest.

Predictable turnaround: Clear timelines and rush options when a line is down.

Secure data: NDAs, controlled sample handling and a secure way to receive results.

Materials Testing Services at Covalent

Covalent runs more than 80 analytical techniques in our 30,000 sq ft Sunnyvale lab, accredited to ISO/IEC 17025 across 60+ methods. Our scientists turn your question into a test plan, run the measurements and explain what the results mean, whether you’re developing a new material, controlling production or investigating a failure. When a project needs a technique we don’t run in-house, we can source it through Covalent Connect, our network of trusted partner labs.

Turnaround is typically 5–7 business days, with rush options available at an extra cost.

Request an Analysis

Frequently Asked Questions

What is materials testing?

Materials testing measures the composition, structure and properties of a material to show how it will perform, why it failed or whether it meets its specification.

What are the main types of materials testing?

Mechanical, chemical and compositional, thermal, surface and interface, microstructural and metallurgical, nondestructive, powder and particle, optical and electrical testing. Most projects combine more than one.

What is the difference between destructive and nondestructive testing?

Nondestructive methods, such as micro-CT, scanning acoustic microscopy and 2D X-ray, examine a part without changing it. Destructive methods, such as cross-sections and tensile testing, cut, load or consume the sample.

How much does materials testing cost?

Pricing depends on the techniques, the number of samples and the turnaround you need. Send us your project and a scientist will reply with a quote, usually within one business day.

How long does materials testing take?

Most projects are completed in 5–7 business days, with rush options available at an extra cost.

Which testing standards do you follow?

We test to ASTM, ISO, IPC and USP standards, including ASTM D638 and ASTM E8 for tensile testing, ASTM D3418 for DSC, ISO 13320 for laser diffraction and IPC-A-610 for electronics inspection, or to a method designed around your question. Tell us the standard you need and we’ll confirm we can follow it.

Is Covalent’s lab accredited?

Yes. Covalent is accredited to ISO/IEC 17025 across 60+ standardized and proprietary analytical methods.

What if I need a test you don’t offer?

We arrange it through Covalent Connect, our network of trusted partner labs, so you still work with one team and receive one report.